# Dig UNO lights stay orange after xlight plays

**URL:** <https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397>\
**Category:** Questions\
**Created:** [October 6, 2023, 1:24am UTC](https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397 "2023-10-06T01:24:58Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![lrehklau](https://avatars.discourse-cdn.com/v4/letter/l/82dd89/32.png) [@lrehklau](https://wled.discourse.group/u/lrehklau)\
**Post date:** [October 6, 2023, 1:24am UTC](https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397/1 "2023-10-06T01:24:58Z")

</div>

I have dig uno and quad, 3 of each. when power on they default to an orange color. I go in and select black to hide

Now I am using in xlights, they work fine however at end of sequence, all my props go dark except the did uno & quad. doesn’t look nice in the yard, stands out like a sore thumb. If I start a sequence all is good until the end.

Is there a way in WLED to turn this off or is it in xlights

these are all ESP32’s, wled 13.3

thx  
les

---

<div class="post-metadata">

**Author:** ![ALDIY](https://yyz2.discourse-cdn.com/free1/user_avatar/wled.discourse.group/aldiy/32/2716_2.png) [@ALDIY](https://wled.discourse.group/u/ALDIY)\
**Post date:** [October 6, 2023, 2:53am UTC](https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397/2 "2023-10-06T02:53:20Z")

</div>

wled 13.3 is very old , go for a recent build from here . [WLED installation (wled-install.github.io)](https://wled-install.github.io/)  
Normally you would see the orange color on leds if the device boots so you can simply setup a boot preset the way you like under settings/leds ( I would go further and check why your device boot if that is the case but test that out after you update your build )

---

<div class="post-metadata">

**Author:** ![lrehklau](https://avatars.discourse-cdn.com/v4/letter/l/82dd89/32.png) [@lrehklau](https://wled.discourse.group/u/lrehklau)\
**Post date:** [October 6, 2023, 11:24pm UTC](https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397/3 "2023-10-06T23:24:35Z")

</div>

Thank you, I did a quick upgrade to 14.0-b6, it did the trick, however in XLIGHTS, I do a an upload to output for that controller, does it with no complaints, however I can no longer access the controller through xlights or wled/IP address. It appeared to corrupt it when I upload outputs, I go back to 13.3 and works great, I test this 3 times same results

les

---

<div class="post-metadata">

**Author:** ![Jinx](https://avatars.discourse-cdn.com/v4/letter/j/c6cbf5/32.png) [@Jinx](https://wled.discourse.group/u/Jinx)\
**Post date:** [October 7, 2023, 3:03am UTC](https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397/4 "2023-10-07T03:03:51Z")

</div>

No need to upload anything from xlights. Just set your outputs/led counts in WLED and don’t have xlights sending the settings to WLED. Things get messed up w/that.

---

<div class="post-metadata">

**Author:** ![lrehklau](https://avatars.discourse-cdn.com/v4/letter/l/82dd89/32.png) [@lrehklau](https://wled.discourse.group/u/lrehklau)\
**Post date:** [October 7, 2023, 7:30pm UTC](https://wled.discourse.group/t/dig-uno-lights-stay-orange-after-xlight-plays/9397/5 "2023-10-07T19:30:45Z")

</div>

Thanks Jinx, that worked this time, I think it was the led count in wled was off.