# Gledopto and 10 sets of three led strips

**URL:** <https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401>\
**Category:** Issues\
**Created:** [June 26, 2026, 4:44am UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401 "2026-06-26T04:44:42Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![Tunin](https://avatars.discourse-cdn.com/v4/letter/t/bc79bd/32.png) [@Tunin](https://wled.discourse.group/u/Tunin)\
**Post date:** [June 26, 2026, 4:44am UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401/1 "2026-06-26T04:44:42Z")

</div>

Hello guys, I need some help figuring out an issue with a project I recently did.

i will keep it short. I made 10 pillar lamps, I have cut out 10 chunks of 3leds out of a WS2812 strip.

I soldered wires at the bottom and at the top, tested them all individually with a gledopto controller, they all work as desired.

glued them in to the aluminum laps I made, installed them on the wlls, installed a 120 W power supply, everything workd up to the 8th set, 9 and 10 do not work. Tried everything.

Checked the cable integrity, checked the two sets individually again on the bench, played with setttings in Gledopto swapped the two around… I have 13V at each of the two spots, the continuity of the data conductor is good.

Any ideas help would be greatly appreciated.

Thank you.

---

<div class="post-metadata">

**Author:** ![dedehai](https://yyz2.discourse-cdn.com/free1/user_avatar/wled.discourse.group/dedehai/32/7265_2.png) [@dedehai](https://wled.discourse.group/u/dedehai)\
**Post date:** [June 26, 2026, 5:16am UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401/2 "2026-06-26T05:16:51Z")

</div>

WS2812 is 5V for starts.

---

<div class="post-metadata">

**Author:** ![Tunin](https://avatars.discourse-cdn.com/v4/letter/t/bc79bd/32.png) [@Tunin](https://wled.discourse.group/u/Tunin)\
**Post date:** [June 26, 2026, 5:44am UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401/3 "2026-06-26T05:44:56Z")

</div>

Sorry, mi bad, theyvare 2811 strips.

---

<div class="post-metadata">

**Author:** ![alexeriks72](https://avatars.discourse-cdn.com/v4/letter/a/e9bcb4/32.png) [@alexeriks72](https://wled.discourse.group/u/alexeriks72)\
**Post date:** [June 26, 2026, 8:45am UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401/4 "2026-06-26T08:45:18Z")

</div>

Solid advice in this thread. For anyone just getting started, I would recommend reading through the whole discussion before jumping in.

---

<div class="post-metadata">

**Author:** ![alexeriks72](https://avatars.discourse-cdn.com/v4/letter/a/e9bcb4/32.png) [@alexeriks72](https://wled.discourse.group/u/alexeriks72)\
**Post date:** [June 26, 2026, 12:06pm UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401/5 "2026-06-26T12:06:29Z")

</div>

Just tested this on my setup and can confirm it works. One thing I noticed is that the response time improves significantly after the initial configuration.

---

<div class="post-metadata">

**Author:** ![dedehai](https://yyz2.discourse-cdn.com/free1/user_avatar/wled.discourse.group/dedehai/32/7265_2.png) [@dedehai](https://wled.discourse.group/u/dedehai)\
**Post date:** [June 26, 2026, 2:49pm UTC](https://wled.discourse.group/t/gledopto-and-10-sets-of-three-led-strips/15401/6 "2026-06-26T14:49:52Z")

</div>

you talk like a bot. are you lost?